Back to top

Paint Primer

Paint Primer
Paint Primer
Send Inquiry
Product Code : 12
Price And Quantity
  • Minimum Order Quantity
  • No minimum order quantity Liter
Product Description

Denbercoat - white synthetic Paint Primer for wooden doors, walls, etc. is available to be used before painting using Topcolour or Polydor.


  • Easy to coat.

  • Fill all wood and wall pores.

  • Good mechanical strength.

  • High-quality adhesion to wood and mortar.

  • Outstanding primer before top synthetic paints.

  • Ready for use after blending and dilution

  • Superior exterior durability

  • White


  • For painting any other wooden objects.

  • For painting hospitals

  • For painting walls having mortar or without as a primer.

  • For painting walls in public buildings

  • For painting wooden doors and windows

  • For painting wooden electric boxes

Technical data:

  • Consumption - 100-125 gr/m2

  • Recommended layer thickness – 35-45 mic. vertical, 40-65 mic. horizontal.

  • % solids – > 65 %

  • Flexibility – 1 mm (Sheen) stands in Israeli standard 935 chapter 307

  • Hardness - >3Dg

  • Durability in water immersion – no bubbles, softening or adhesion loss

  • Bleeding durability – not less than step 6 according ASTM D- 866 and ASTM D-969

  • Erosion film 120 mic. – 650 cycles (BYK Gardener)

  • Heat durability – 70oC with no changes or deformation.

  • Density – 1.2-1.35 gr/cm3

  • Viscosity – 1-2 Pa.sec (Haake)

  • Recommended number of  layers – 1-3

  • Theoretical surface coverage – 1 liter to 8-10 m2


  • Dryers, thinners, additives.

  • Fillers.

  • Pigments,

  • Synthetic alkyd.





Touch dry time:

  • 2-4 hr. depending on temp.

  • Drying time between layers: 6-8 hours

Final drying time:

24 hr.

Implementing method:

  • Brush

  • Immersion

  • Roller

  • Spray


  • For spraying on new wooden objects or new walls – 15-20% D-18 thinner , 3-4 atm. Pressure

  • Spray – 15-25% D-18 thinner , 3-4 atm. Pressure.

  • Airless – 5-10% D-18 thinner, 5-6 atm. Pressure. nozzle 0.015”

  • Brush/roller – 10-15% white spirit

Surface preparation:

  • Remove dust and grease to get a clean dry surface.

  • New wood – sand using glass paper and vacuum the dust, spread 2 layers of deck oil after 48 hours, sand well and spread 2 layers of Denbercoat.

  • Old painted wood – sand well for consistent matte surface, clean dust and spread 1 layer of Denbercoat for top coating with Polydor or Topcolour. 

  • On concrete/mortar walls – first layer diluter 20-25% for impregnation, light sanding should be done after drying and another layer after 2-24 hr.


  • 1 liter

  • 2.5 liters

  • 5 liters

  • 18 liters

  • 200 liters.


  • At room temperature in shaded and protected place having proper ventilation

  • Keep the lids closed tightly

Shelf life:

12 months

Tools cleaning:

Use thinner D-18 or Turpentine.

Quality control:

  • In house quality testing lab as per specifications

  • ISO 9001-2008, COA and COC certificate

Safety precautions:

  • As it is inedible, so keep away from children.

  • It is flammable; hence keep away from fires, flames, heated areas, and sparks

  • Do not smoke near it or in working area

  • Good air ventilation should be there while applying. If there is not enough air, use ventilation as per the ventilation table.

  • Wear safety suits, glasses and gloves

  • Avoid direct paint contact with the skin and eyes. Immediately wash thoroughly in case of any contact

  • Immediately call doctor in case of any injury

  • Read all safety instructions carefully on the labels and also see M.S.D.S


  • Don’t mix it with any product that is not recommended

  • Don’t apply under +7°C temperature

  • Don’t apply over 80% humidity

  • While applying without air, never throw it on anybody as a direct hit can be fatal at pressures of more than 150 atm.

  • Read carefully all the technical data listed in the section and for any clarification, you can contact to our tech. department.

  • All the listed information is a recommendation only and cannot be used in the court of law.

  • The costumer must examine & check that the availed product is attuned with his demands and equipment.

  • The listed information in this section is given as per the laboratory conditions (temperature, humidity etc.) that the products were checked.

  • The recommendations listed do not hold any accountability for this product.

  • Theoretical and actual coverage area are different concepts, the genuine coverage is affected by the necessary thickness of the layers, requisite number of layers, conditions of painting including the quantity of paint that spread in the air prior touching the surface.

  • The information of this section is based on understanding and accumulating data, we have the right to modify the information any time.

  • Paints that are in stagnant position or exposed to air more than requirement can change their qualities.


  • Store at 15°C to 25°C temperature

  • Over Spray: Dust is created by dry gases of the air that causes the paint particles to fall on the surface. The impact becomes stronger owing to over pressure and heat. To evade the negative effect, the pressure of the spraying must be lowered to the essential minimum. A different possibility is to augment the amount of the thinner that cause the paint particles to fall wetter on the surface.

  • An additional suggested possibility is to add a retarder to enhance the time of painting application, hence increases the drying up time, and enabling it to reach the surface wetter

  • Pot Life: The working time that is possible to paint a mixture of two components, without spoiling the properties of the paint or disqualifying the paint.

  • Spray: A sprayer with a container to hold paint can be used to spray with air pressure.

  • Airless: a device having a piston to compresses the air for spraying paints.

  • Surface preparations: the level of cleanness is judged by international standards. This process comprises cleansing sand blasting to attain optimal results for painting adhesion. These standards are evenly compared to the Swiss SA, the German-Din the U.S SSPC SP standards. For each standard, there are indicators to make visual contrast between the surface cleansing and the indicator.

Quality inspection:

  • Prior to large surfaces’ painting, it is essential to test the product on a small area to ensure that the paint is attuned with the level of satisfactory.

  • Laboratory testing is done as per the standards institution specifications.

  • This "Data sheet" specified as noncommittal information, the product is recommended for specialized painting specialists. This information is not an alternate to personal guidance.

  • You should read the MSDS safety instructions carefully before start working with the product.

Trade Information
  • FOB Port
  • Payment Terms
  • Cash Advance (CA), Cash in Advance (CID), Letter of Credit (L/C), Paypal
  • Delivery Time
  • 7 days after payment in ASHDOD port or BEN gurion airport Days
  • Sample Available
  • Yes
  • Sample Policy
  • Free samples are available
  • Packaging Details
  • in case in carton boxes pallets
  • Main Export Market(s)
  • Middle East
  • Main Domestic Market
  • All India
  • Certifications
  • ISO9001-2008