Anti Flame Paint

Flexible polyvinyl acetate Anti Flame Paint water dilution to prevent fire spread as well as smoke ejects. This is ideal for interior as well as exterior coating. This highly viscous paint is ideal for coating metal building elements and prevents collapse during fire. Intumescent and cut off the effects of heat when steel is on fire. It contains materials that avert the development of flame combustion and spreading of fire. It contains materials to reduce smoke. It can be diluted with water due to unique molecular structure.

• Pass Standards Institute in South Africa SABS British standard BS-476 P20 and P21 test no. # FPE/84933/08A

• Pass the Israeli Standards Institute standard 755 rank 5. Test no.  8111202204

• Pass the Israeli Standards Institute standard 931, time protection 3 hours. Test no.  93119149631

Properties: 

• PVA Intumescing plaster/paint, appropriate for interior and exterior uses

• Provides protection from fire for 3 hours between floors

• A great adhesion to glass wool

• Easily implemented by spreading using spray gun, airless, roller or brush after diluting with water

• Flexible

• Crack proof

• Prevents the spread of fire

• Emits gas to shutdown flame.

• Depressing smoke

• Intumescing up to 60 times

• Can be applied in 500 micron layer

• Appropriate for protecting electric cables

• Quick drying

• Ready to recoat every 4-6 hours

Applications:

• Columns

• Metal structures

• Steel beams

• Steel roof support columns

Technical data:.

• Density – 1.3- 1.5 gm\cm3

• Effective coverage – as per the thickness of fire protection tables and per profile steel fire protection according to the time of fire protection required.

• Erosion -120 microns-760 cycles (BYK Gardner) ASTM

• Flexibility – 1 mm (Sheen)

• Hardness – 10 Dg (Erichsen)

• Layer thickness recommended – spraying -200 microns wet layer, brushing – 500 microns wet layer.

• Number of layers – as the number essential to get the thickness required

• Viscosity – 20,000 cps (Brookfield)

Contains:

• Fillers and pigments.

• Special flex sizing materials.

• Special PVA

• Water and additives

Shades:

Standard white

Gloss:

Matte. 

Drying time:

• 30 minutes for thin layer

• Between layers: 2-4 hours. Final: 6 hours.

Application methods:

• Brushing, roller, spraying, or spread with spatula.

• The first layer is suggested dilution and spraying  5 atmosphere pressure

• Second layer and more are done by spraying or brush spreading or scrolling using flexible plastic spatula. It can be applied by airless ratio pressure 1:45 and higher nozzle 0.2”-0.27”

Dilution:

• Water.

• Spraying  –  first layer - 30%, second layer - 5%

• Brush/roller-10-20%

Surface preparation:

Clean the surface from dust, dirt and loose paint

Primary paint:

• Epoxyden primer brominated (resistant to fire).

• Tutgum antiflame. 

Packaging:

• 5 liters

• 18 liters

• 200 liters

Storage:

• At room temperature in shaded and protected place having proper ventilation

• Keep the lids closed tightly

Shelf life:

12 months

Cleaning tools:

Water at the end of painting.

Quality control:

• In house quality testing lab as per specifications

• ISO 9001-2008, COA and COC certificate

Safety precautions:

• As it is inedible, so keep away from children.

• It is flammable; hence keep away from fires, flames, heated areas, and sparks

• Do not smoke near it or in working area

• Good air ventilation should be there while applying. If there is not enough air, use ventilation as per the ventilation table.

• Wear safety suits, glasses and gloves

• Avoid direct paint contact with the skin and eyes. Immediately wash thoroughly in case of any contact

• Immediately call doctor in case of any injury

• Read all safety instructions carefully on the labels and also see M.S.D.S

Warnings:

• Don’t mix it with any product that is not recommended

• Don’t apply under +7°C temperature

• Don’t apply over 80% humidity

• While applying without air, never throw it on anybody as a direct hit can be fatal at pressures of more than 150 atm.

• Read carefully all the technical data listed in the section and for any clarification, you can contact to our tech. department.

• All the listed information is a recommendation only and cannot be used in the court of law.

• The costumer must examine & check that the availed product is attuned with his demands and equipment.

• The listed information in this section is given as per the laboratory conditions (temperature, humidity etc.) that the products were checked.

• The recommendations listed do not hold any accountability for this product.

• Theoretical and actual coverage area are different concepts, the genuine coverage is affected by the necessary thickness of the layers, requisite number of layers, conditions of painting including the quantity of paint that spread in the air prior touching the surface.

• The information of this section is based on understanding and accumulating data, we have the right to modify the information any time.

• Paints that are in stagnant position or exposed to air more than requirement can change their qualities.

Clarifications:

• Store at 15°C to 25°C temperature

• Over Spray: Dust is created by dry gases of the air that causes the paint particles to fall on the surface. The impact becomes stronger owing to over pressure and heat. To evade the negative effect, the pressure of the spraying must be lowered to the essential minimum. A different possibility is to augment the amount of the thinner that cause the paint particles to fall wetter on the surface.

• An additional suggested possibility is to add a retarder to enhance the time of painting application, hence increases the drying up time, and enabling it to reach the surface wetter

• Pot Life: The working time that is possible to paint a mixture of two components, without spoiling the properties of the paint or disqualifying the paint.

• Spray: A sprayer with a container to hold paint can be used to spray with air pressure.

• Airless: a device having a piston to compresses the air for spraying paints.

• Surface preparations: the level of cleanness is judged by international standards. This process comprises cleansing sand blasting to attain optimal results for painting adhesion. These standards are evenly compared to the Swiss SA, the German-Din the U.S SSPC SP standards. For each standard, there are indicators to make visual contrast between the surface cleansing and the indicator.

Quality inspection:

• Prior to large surfaces’ painting, it is essential to test the product on a small area to ensure that the paint is attuned with the level of satisfactory.

• Laboratory testing is done as per the standards institution specifications.

• This "Data sheet" specified as noncommittal information, the product is recommended for specialized painting specialists. This information is not an alternate to personal guidance.

• You should read the MSDS safety instructions carefully before start working with the product.